Resize your LinkedIn profile banner
Choose the photograph or graphic you want to use behind your personal LinkedIn profile. The editor exports a 1584 × 396 JPG, a 4:1 canvas. Use Center crop to cover the full rectangle or Fit with padding to retain every edge. If you use padding, choose a color that matches the outer edge of the source. Preview the result before downloading it. Upload that JPG through the background photo controls on your profile and review its positioning in the interface.
Give the profile picture room
A LinkedIn cover sits alongside other profile elements, so a banner that looks balanced by itself may feel crowded once it appears above your profile. Keep essential type and logos away from the lower left, where the profile photo can overlap in some views. Leave margins around important details and check the resulting profile on both desktop and mobile. A plain background, intentional negative space, and one focal point typically survive the change in scale better than a full contact card or a dense strip of text.
Work with a wide source
Horizontal photos with extra space above and below the subject are easier to adapt to a 4:1 cover. A centered portrait source requires a strong crop, and its most important feature may fall outside the visible strip. If your source is tall, Fit with padding preserves the photograph and gives you room to use a complementary color on the sides. If your source is a designed banner with type near the edges, export the design close to the final ratio before using this tool.
Check the final graphic before updating your profile
Preview at a width roughly comparable to the visible cover on your phone. Look for clipped letters, a confusing crop, or detail that becomes too fine to read. Strong contrast is especially valuable when the banner contains professional credentials or a short tagline. Keep a copy of the high-resolution source so you can revise the design later. If a narrow crop cuts through the subject, return to the editing file and move the subject rather than repeatedly resizing a version that has already lost its edges.
Decide what the banner should communicate
A personal profile banner can support a portfolio, a job search, or an introduction to the kind of work you do. A designer might use a cropped photograph of a published project. An independent consultant might use a quiet layout with one readable phrase. A photographer might choose a wide composition whose visual subject is apparent even when shown very small. Before resizing, choose one piece of information that should remain obvious and make sure it still makes sense beside the profile picture and headline. If it is important text, repeat it in a readable part of the profile as well.
This preset is for the personal profile layout. Check which LinkedIn placement you are preparing because a company page can use a different frame. Keep separate working versions if you manage both. A print banner, a presentation cover, and a profile image may come from the same design, but a wide and shallow profile frame gives them very different crops. Plan for the profile layout from the start instead of trying to retain every visual detail from a different design.
Choose a crop or padding for the 4:1 canvas
The tool exports a 1584 × 396 JPG. Center crop scales the source until it covers the 4:1 canvas, then removes the parts that extend beyond it. This option works well with already wide scenery, textures, and photos with substantial free space. A square or tall graphic loses much of its height when cropped to a 4:1 strip. Before selecting this option, check whether a headline or face close to the top and bottom would disappear. Reposition important elements in the original editor if they are too far from the usable strip.
Fit with padding keeps the complete source visible. An ordinary photograph can look narrow inside a 4:1 canvas, so review how much empty space the preview creates. A single padding color works best when it fits the palette of the original. Choose a deliberate contrasting color if the distinction is part of the design. If your main element becomes tiny when everything fits, consider preparing a wider source and grouping the key elements in a shallow horizontal band. A few carefully placed elements can be easier to understand at profile size.
Keep any small type in an editable source. Once typography is baked into a JPG, shrinking or enlarging it can make the edges less clear. Use strong enough contrast and avoid relying on very thin lines for a divider or a logo. If the source includes a transparent logo, check how it looks after flattening to JPG. Inspect the whole export for unintended panels, especially if the original transparent area is a large part of the image.
Check the final banner on the actual profile
First verify the file dimensions, then preview the banner together with your profile photograph. Look at desktop and mobile if you can. Depending on the application layout, the avatar can overlap the lower part of the banner and the visible area can vary. Move any important text or design elements away from the overlap in the source and export again. Check the image before and after saving, since the preview in an editor and the rendered profile can show a different crop.
Compare the approved banner with your actual headline and adjacent text. If the image is the only place where a key detail appears, check whether it is still legible in a compact view. Confirm names, branding and any current dates. If you keep several banners for different periods, save different export filenames and maintain one editable source per version. It is easier to update a headline or swap a project photo from a dated source than to edit a profile JPG that has already been uploaded and resized.
Before resizing a collage, open it at approximately the size at which the profile will show it. Pick the photograph that carries the most relevant detail and consider giving it more room in the source design. A grid of several pictures can become hard to read once the banner is compressed into a shallow strip. Try removing a less relevant picture or use it in the featured section of the profile instead. Compare the updated banner within the profile context, where the avatar and headline already provide information. You can then let the banner concentrate on its strongest visual rather than filling every empty part.
If you create a few versions for different purposes, test each export on its own before switching the live profile. Check the full spelling of company or project names and make sure a logo still has its intended shape. When you hand the banner to someone else, give them the finished 1584 × 396 JPG and the editable source as separate files. Include the padding color and framing choice if those settings were important to reproduce the result. After a collaborator uploads the file, ask them to check the crop in their own profile view, since it can differ from what you saw in the source editor.
Frequently asked questions
Is this for a personal profile or a company page?
The 1584 × 396 preset is for a personal profile background. LinkedIn company pages use a separate cover layout, so use the page’s current specifications when preparing an organization’s assets.
Will the crop stretch my photo?
The horizontal and vertical scales stay equal. Center crop cuts off the area outside the 4:1 canvas. Fit with padding preserves the entire source within the canvas.
Why is an element hidden only on my phone?
LinkedIn can place profile elements differently depending on the viewport. Give logos and text extra room and inspect the updated profile on the devices that matter to you.
How can I keep a complex design legible?
Reduce text to a short phrase, keep a consistent background under it, and export from the highest-quality source available. Preview the cover as a small strip, since the full-size JPG can make marginal text look more readable than it will be.